Seat covers, preassembled door panels with armrests sewn on, rear trim panels. Rear armrest and top piston covers, windlace set, sunvisors. Vinyl covered kick panels, Convertible top boot. Daytona carpet set and floor mats. Oversize Shipping Rates Apply on Door Panels.

All vinyl sewn with Saddle Stitched seat caps and our reproducted Tree Bark embossed seat insert vinyl with variegated line flecks. Pleated vinyl on the rear of the front seat back rests. All correct 1956 colors. Matching seat shell vinyl & 4 silver buttons. Heavy listings sewn on. 22 lbs.

This is the front seat cover for the 1956 Convertible. Heavy weight vinyls with heavy White thread saddle stitched seat caps, embossed Bark pattern insert vinyl with Black & Ivory flecks. Pleated vinyl on the rear of the front seat backs. All installation listings attached. 4 Silver buttons. 12 lbs

This is a reproduction of the 1956 Convertible seat insert vinyl in all the correct insert colors. Heavy weight 54" wide with or without the flecked lines. 3 lbs per yard.

Made to conform to the front split bench frame of the 1956 Convertible. High desity foam with 1/2" layer of foam topper pad. We feel our layered foam works better than molded foam. 

Rear bench seat seat high density foam with 1/2" foam top layer. This is what we use in our installation department and we do not have to add any other foam or batting. Minor trimming required. 

These Silver Mylar covered buttons match the seat welt. Exact pattern as the originals. They are sold individually with tighting retainers. 4 required per 1956 Bel Air. Free Shipping.

Replace your rusty, unusable front seat backrest springs with this new reproduction unit. Easy to install. Sold in lefts or rights. Please state which side or both when ordering. 10 lbs.

This is the two section metal seat springs for bottom cushion and back rest. Shaped and sized to fit properly. 50 lbs.

All Chevy models used these to secure the seat shells to the seat frame. These mounting brackets are used on 2 door, 4 door and Station Wagon seats. Sold individually in right or left. 1 lb each.

Seat shell stainless steel trim strips. Installation prongs are on the underside and easy to attach. Used on 2 door and 4 door models. Sold individually. 0.5 each.

Interior vinyl as used on seat covers, door panels, seat shells, sunvisors. Heavy weight 54" vinyl in all the factory 1956 colors and Haircell grain. 3 lbs per yard. price per yard

1956 Bel Air Models used this Pleated vinyl on the door panels and behind the front seat back rests. We can make it in any of the 1956 colors or a color of your choice. Sold in sheets 27" x 53" with padded back. 5 lbs per sheet.

New front door panels and rear trim panels. Die cut waterproof boards with new galvanized door edge metal bands with nails. Armrest and rubber pads included and installed. Sewn front armrest covers. Upper pleated vinyl, sewn rear armrest covers and top piston covers. Vinyl covered kick panels. Extra vinyl. 88 lbs in Two boxes.

Rear armrest and top piston vinyl covers installed $175.00

A pair of correctly contoured cut and sewn on our double needle machine. For the exact shape and appearance of original. Using interior vinyl of your choice. These are for professionals with a long arm sewing machine to install.

This exact reproduction is for the front doors, rear quarter trim panels and the lower rear armrest moldings. 8 piece set. 5 lbs.  Free installation with Preassembled door order.

Armrest Support Bases; For the Bel Air front doors, molded ABS into the correct shape for the 1956 Convertible.  2 lbs.

This is an exact reproduction of armrest rubber pad, even the Black color is correct. Contour shaped and fit excellent on original armrest bases or Ciadella bases. Sold in pairs at this low price of $69.00. 2 lbs.

Sold individually. These are stamped metal door panel finger cups for the front door panels, with two screw holes. 1 lb.

Sold individually. This L shaped bracket screws to the door frame and the armrest attaches with two screws from the finger cup.   .05 lb.

These door panel boards are presicion die cut for the front and rear doors. Using waterproof boards with armrest openings, door handles & window crank holes and trim attaching slots. Sold in pairs @ $49.95 per pair 10 lbs per 2 door boards.

Galvanized metal door edge metal bands that go on the door panel edges and the bottom to attach the door board to the door. Serrated edges on one side to hold the door panel trim tight. Nails included. 4 lbs.

These are precision die cut for the 1956 Convertibles, out of waterproof board. Holes for stainless moldings and push outs for window cranks or power widow switches. Sold in pairs. 5 lbs.

For all years. These fit between the door panel and the edge metal band, and just need crimping to secure in place. Sold in groups of 10  for $7.50 with Free Shipping.

These are a pair of matching seat belts for the driver and passenger, with chrome aircraft chrome quick release buckels. 68" in length, In many colors. Priced per pair 3 lbs.

Sunvisors using new boards and posts. Covered with smooth Haircell matching interior vinyl with colored binding to match. Stainless tips. price per pair 5 lbs

Matching interior vinyl windlace set (4 pieces) made for the 1956 Convertible. Vinyl covered 1/2" round sponge rubber with dash side flaps and easy to install slide in kick panel cord. 3 lbs

These windlace end metal supports are for 1955-1957 2 door hardtops, Nomads and convertibles. They screw on to the upper rear quarter door jamb. Comes with correct black rubber tip ends to attach to your rear windlace strips. 1 lbs.

This windlace set is made with the upper rear 1/4 panel mounting supports and rubber end stops. For all 1955 - 1957 Convertibles. Sewn with the front kick panel slide in cords and dash flaps. Rears staple on. In all the correct colors for your year. 5 lbs.

Die cut to fit properly and be exactly like originals. Black panel boards die cut to correct shape and fit. $15.95 pair or we will sell you a pair of vinyl covered kick panels to match the interior trim vinyl. $55.95 pair. 2 lbs.

 Ciadella was the first to correctly manufacture the low loop Daytona carpet in 1980. We have all the correct colors in this beautiful carpet with rubber backing. Comes with correct vinyl binding and heel pad. Double seamed at the top of the hump and at the door opening sides as they did from the factory. And jute padding underside. 20 lbs.

Reproduced low loop, tightly woven nylon carpet material. 54" wide with latex foam underside. Sold 54" x 36" per running yard. 10 lbs per yard.

Front & rear 4 piece set. Laytex foam underside, complete vinyl edge binding to match the interior vinyl color. Available in all the Daytona carpet colors.  Mats have nibbed backing. 10 lbs.

  FREE floor mats with interior purchase.

High quality cut and sewn Nylon loop carpet. All matching interior edge binding and heel pad. Jute padded underside. Made in our shop or if your Chevy has bucket seats we can get you a one piece molded carpet. Many colors available, just ask. 20 lbs. 

Heavy weight GM Pinpoint grain vinyl. Cut from tested and true patterns. Heat sealed side panels, brass zipper rear window. Includes top pads, and front edge round windlace. Available in many colors. Tinted back window available. 20 lbs

Rear convertible top storage well. Cut and sewn to proper contour and shape using heavy weight black canvas. 3 lbs.

Made out of matching interior vinyl with heavy support edge vinyl under snap areas. Vinyl edge binding. In all the original colors or any colors you choose. Chrome snaps included and your upholstery person or yourself can attach them for a perfect fit. 7 lbs

1956 Black rubber countour molded mat with spare tire cut out. Molded vertical lines, exactly like the original. 16 lbs.

This trunk mat is made using our low loop "Daytona" carpet material that has latex foam backing. Cut to properly fit the trunk floor contour and shape, with or without spare tire cut out opening. Matching interior vinyl edge binding sewn on the outside edges to duplicate the interior floor carpet. 9 lbs.